Bosch Security

The Bosch Security integrated system provides access control integration.

Definitions

Area — An area encompassing many points, outputs, or doors that will be the source of alarms.

Point — An individual sensor or point that is used to trigger an alarm in its area.

RPS — Remote Programming Software. Bosch software is used to remotely program control panels.

Setup

See the Data Servers page for information on configuring driver communication.

Compatibility

The Bosch Security integrated system is compatible with B and G Series panels.

Prerequisites

Software Minimum Version
IPFusion — Bosch Security 1.4
.NET Framework 4.7.2

When completing your setup, be sure to have the Bosch Security documentation available for reference.

Ports

These ports must be open in your network firewall for the integration to work.

Purpose Default Value Configurable
Communication Settings 7700 Yes
Dataserver 8082 Yes
Debug Tools 9463 No

Communication Configuration

In the integrated system configuration panel, you will find the Communication Settings. The below information is required.

Note: If you are connecting to multiple panels, you will need to add another instance of the Bosch Security system to your project for each panel.
Address The IP Address or host name of the Bosch Security control panel.
Port The Port number for the Bosch Security control panel connection.
Product ID The Bosch Security control panel Product ID.
Password The automation pass code of the Bosch Security control panel.
Note: Red X indicates an invalid or out of range value given for field.

Assets

Area Asset

This asset represents an area in the Bosch Security control panel.

Required Property Grid Fields

Area Number The Area Number in the Bosch Security control panel.

View all properties

Supported States

Acknowledged An asset alarm has been acknowledged.
Alarm - Burglary Alarm A burglary has been detected.
Alarm - Burglary Supervisor Early signs of a burglary have been detected.
Alarm - Burglary Trouble A burglary has been detected and there is an issue (such as power loss).
Alarm - Fire Alarm A fire has been detected.
Alarm - Fire Supervisor Early signs of a fire have been detected.
Alarm - Fire Trouble A fire has been detected and there is an issue (such as power loss).
Alarm - Gas Alarm Gas has been detected.
Alarm - Gas Supervisor Early signs of there being gas have been detected.
Alarm - Gas Trouble Has been detected and there is an issue (such as a low battery).
Alarm - Personal Emergency Triggered by a user experiencing an emergency.
Alarm - Unknown An alarm with an unknown source has been triggered.
All On - Entry Delay The area is armed. There is a delay before triggering an alarm on entry to the area.
All On - Exit Delay The area is armed. There is a delay before triggering an alarm on exit from the area.
All On - Instant Armed The area is armed. There is no delay before triggering an alarm.
Area Disabled The area is unarmed.
Area On The area is armed.
Fault An issue has been detected in a connected asset.
Masked The asset has been masked over its true state.
No Communication Communication has been lost with the driver or asset. This status can also occur if the communication configuration for the system or asset is invalid.
Note: This status is required in all status tables.
Not Ready to Arm The area is disarmed and not ready to be rearmed.
Not Set The area is not armed.
Part On - Delay Part of the area has delayed arming.
Part On - Entry Delay Part of the area is armed. There is a delay before triggering an alarm on entry to the area.
Part On - Exit Delay Part of the area is armed. There is a delay before triggering an alarm on entry from the area.
Part On - Instant Part of the area is armed. There is no delay before triggering an alarm.
Ready to Arm The area is disarmed and ready to be rearmed.

See the Configure a Status Table page for more information on configuring status tables.

Supported Commands

Acknowledge Acknowledge an asset alarm.
Away Arm Arm the area for when no one is to be in the area.
Cancel Deselects all selected assets.
Disarm Disarm the area.
Force All On - Delay Arm the entire area with a delay.
Force All On - Instant Arm the entire area immediately.
Force Away Arm Arm the area with an away arm.
Force Part On - Delay Arm part of the area with a delay.
Force Part On - Instant Arm part of the area immediately.
Force Stay One Alarm Arm the area for when no one is to be entering, but there will be someone in the area.
Mask Mask the asset's true state.
Reset Resets the asset to its true hardware state.
Set All On - Delay Turn on all assets in the area with a delay.
Set All On - Instant Turn on all assets in the area immediately.
Set Part On - Delay Turn on some of the assets in the area with a delay.
Set Part On - Instant Turn on some of the assets in the area immediately.
Stay One Arm Arms the system to alarm for entry or exit of the area only.

See the Command Tables page for more information on configuring command tables.

Door Asset

This asset represents a door in the Bosch Security control panel.

Required Property Grid Fields

Door Number The Door Number in the Bosch Security control panel.

View all properties

Supported States

Acknowledged An asset alarm has been acknowledged.
Cycling The door is being temporarily unlocked.
Fault An issue has been detected in a connected asset.
Inactive This door will not be included for alarms.
Learn This state is used to configure a key fob or card.
Locked The door is locked.
Masked The asset has been masked over its true state.
Missing The system can not find this door.
No Communication Communication has been lost with the driver or asset. This status can also occur if the communication configuration for the system or asset is invalid.
Note: This status is required in all status tables.
Normal The asset is online and in its default state.
Secure The door is closed and locked.
Unlocked The door is unlocked.

See the Configure a Status Table page for more information on configuring status tables.

Supported Commands

Acknowledge Acknowledge an asset alarm.
Cancel Deselects all selected assets.
Cycle Cycles the door (unlock, then lock).
Mask Mask the asset's true state.
Reset Resets the asset to its true hardware state.
Secure Sets the door to a Secure state (locked).
Terminate Secure Mode Sets the door to its default state.
Terminate Unlock Mode Sets the door its default state.
Unlock Unlocks the door.

See the Command Tables page for more information on configuring command tables.

Output Asset

This asset represents an output device in the Bosch Security control panel.

Required Property Grid Fields

Output Number The Output Number in the Bosch Security control panel.

View all properties

Supported States

Acknowledged An asset alarm has been acknowledged.
Fault An issue has been detected in a connected asset.
Masked The asset has been masked over its true state.
No Communication Communication has been lost with the driver or asset. This status can also occur if the communication configuration for the system or asset is invalid.
Note: This status is required in all status tables.
On The asset is currently on.
Off The asset is currently off.

See the Configure a Status Table page for more information on configuring status tables.

Supported Commands

Acknowledge Acknowledge an asset alarm.
Cancel Deselects all selected assets.
Mask Mask the asset's true state.
Reset Resets the asset to its true hardware state.
Set On Turn the asset on.
Set Off Turn the asset off.

See the Command Tables page for more information on configuring command tables.

Point Asset

The point asset is a representation of a point in the Bosch Security control panel.

Required Property Grid Fields

Point Number The Point Number in the Bosch Security control panel.

View all properties

Supported States

Acknowledged An asset alarm has been acknowledged.
Fault An issue has been detected in a connected asset.
Masked The asset has been masked over its true state.
No Communication Communication has been lost with the driver or asset. This status can also occur if the communication configuration for the system or asset is invalid.
Note: This status is required in all status tables.
Normal The asset is online and in its default state.
Open The point's circuit has been opened. This can be used to trigger an alarm.
Rx2 Receiving information over an Rx2 signal.
Rx3 Receiving information over an Rx3 signal.
Short An issue has been detected in the point's hardware.
Unassigned The point is not assigned to a physical piece of hardware.
Unknown The state can not be determined.
Bypass This state is used to bypass an alarmed state.
Note: Bypass must be used as a multistate status alongside its regular state. The default is Bypass and Normal.

See the Configure a Status Table page for more information on configuring status tables.

Supported Commands

Acknowledge Acknowledge an asset alarm.
Cancel Deselects all selected assets.
Mask Mask the asset's true state.
Reset Resets the asset to its true hardware state.
Bypass Temporarily silences the current status of the point asset. This allows the point status to not affect the ability to arm the system.
Unbypass Removes the bypassed state from the point.

See the Command Tables page for more information on configuring command tables.

System Asset

This asset represents the connection state of the Bosch Security control panel.

View all properties

Supported States

Acknowledged An asset alarm has been acknowledged.
Attempting Connection The system is currently trying to connect with Runtime.
Battery Low The battery has a low charge.
Battery Missing There is no battery in the control panel.
Battery OK The battery is in the panel and charged.
Connected The control panel is connected to Runtime.
Disconnected The control panel is not connected to Runtime.
Disconnecting The control panel is disconnecting from Runtime.
Fault An issue has been detected in a connected asset.
Masked The asset has been masked over its true state.
No Communication Communication has been lost with the driver or asset. This status can also occur if the communication configuration for the system or asset is invalid.
Note: This status is required in all status tables.
Power Failed The control panel is unable to get power.

See the Configure a Status Table page for more information on configuring status tables.

Supported Commands

Mask Mask the asset's true state.
Acknowledge Acknowledge an asset alarm.
Reset Resets the asset to its true hardware state.
Cancel Deselects all selected assets.

See the Command Tables page for more information on configuring command tables.

Troubleshooting

Logs from the driver and Runtime can be viewed in the Debug Tools client. These messages contain information which can provide further context for issues during initialization, or while actively running. This can help diagnose problems.