DSC PowerSeries

Setup

See the Data Servers page for information on configuring driver communication.

Compatibility

The DSC PowerSeries integrated system is compatible with the below panels and is tested using the TL280R panel.

3G2080
3G2080R
TL280
TL280R
TL2803G
TL2803GR
PCL-422

Prerequisites


Software	Minimum Version
IPFusion — DSC PowerSeries	1.0
.NET Framework	4.7.2

When completing your setup, be sure to have the DSC PowerSeries documentation available for reference.

Ports

These ports must be open in your network firewall for the integration to work.


Purpose	Default Value	Configurable
Communication Settings	3073	Yes
Dataserver	9648	Yes
Debug Tools	9649	No

Communication Configuration

In the integrated system configuration panel, you will find the Communication Settings. The below information is required.

Table 1. Connection Settings
Address	The address of the server hosting the DSC PowerSeries driver.
Port	The Port number for the DSC PowerSeries control panel connection.

Table 2. Authentication
Integration Identification Number	The defined Integration Identification Number for your DSC panel.
Integration Access Code	The Integration Access Code configured when setting up your DSC panel.
Master Code	The Master Code configured when setting up your DSC panel.

Note: Red X indicates an invalid or out of range value given for field.

Assets

System Asset

This asset represents the connection to the DSC panel.

View all properties

Supported States


Normal	The asset is online and in its default state.
Masked	The asset has been masked over its true state.
Fault	An issue has been detected in a connected asset.
Acknowledged	An asset alarm has been acknowledged.
No Communication	Communication has been lost with the driver or asset. This status can also occur if the communication configuration for the system or asset is invalid. Note: This status is required in all status tables.

See the Configure a Status Table page for more information on configuring status tables.

Supported Commands


Mask	Mask the asset's true state.
Acknowledge	Acknowledge an asset alarm.
Reset	Resets the asset to its true hardware state.
Cancel	Deselects all selected assets.

See the Command Tables page for more information on configuring command tables.

Partition Asset

This asset represents a partition in the DSC system.

Required Property Grid Fields


Partition ID	The identifier for the partition this asset represents.

View all properties

Supported States

Note: This asset supports multistate, meaning the asset can be in multiple statuses at once.


Masked	The asset has been masked over its true state.
Fault	An issue has been detected in a connected asset.
Acknowledged	An asset alarm has been acknowledged.
No Communication	Communication has been lost with the driver or asset. This status can also occur if the communication configuration for the system or asset is invalid. Note: This status is required in all status tables.
Disarmed	The partition is disarmed.
Stay Armed	The partition is armed in stay mode.
Stay Armed With No Entry Delay	The partition is armed in stay mode without a delay given for people to enter/exit the area first.
Away Armed	The partition is armed in away mode.
Away Armed With No Entry Delay	The partition is armed in away mode without a delay given for people to enter/exit the area first.
Night Mode Armed	The partition is armed in night mode.
In Alarm	An alarm is active within the partition.
Ready	The partition is ready to be armed.
Not Ready	The partition is not ready to be armed.

See the Configure a Status Table page for more information on configuring status tables.

Supported Commands


Reset	Resets the asset to its true hardware state.
Mask	Mask the asset's true state.
Cancel	Deselects all selected assets.
Acknowledge	Acknowledge an asset alarm.
Disarm	Disarms the partition.
Arm Stay Mode	Arms the partition in stay mode.
No-Entry Arming in Stay Mode	Arms the partition in stay mode without providing a delay.
Arm Away Mode	Arms the partition in away mode.
No-Entry Arming in Away Mode	Arms the partition in away mode without providing a delay.
Arm Night Mode	Arms the partition in night mode.
Activate Output	Activates a specified output ID.
Deactivate Output	Deactivates a specified output ID.
Toggle Output	Activates a deactivated output by ID, and vice versa.

See the Command Tables page for more information on configuring command tables.

Zone Asset

This asset represents a zone in the DSC system.

Required Property Grid Fields


Zone ID	The identifier for the zone this asset represents.

View all properties

Supported States

Note: This asset supports multistate, meaning the asset can be in multiple statuses at once.


Masked	The asset has been masked over its true state.
Fault	An issue has been detected in a connected asset.
Acknowledged	An asset alarm has been acknowledged.
No Communication	Communication has been lost with the driver or asset. This status can also occur if the communication configuration for the system or asset is invalid. Note: This status is required in all status tables.
Bypassed	The zone is currently bypassed.
Not Bypassed	The zone is not bypassed.
In Alarm	An alarm is active in the zone.
No Alarm	There are no active alarms in the zone.
Open	The zone input is currently in an open-circuit state.
Closed	The zone input is currently in a closed closed-circuit state.

See the Configure a Status Table page for more information on configuring status tables.

Supported Commands


Mask	Mask the asset's true state.
Acknowledge	Acknowledge an asset alarm.
Reset	Resets the asset to its true hardware state.
Cancel	Deselects all selected assets.
Bypass	Bypasses the zone.
Unbypass	Removes the bypass from the zone.

See the Command Tables page for more information on configuring command tables.